What is an LG Dishwasher OE Error?

It is an unpleasant experience when the LG dishwasher fails to work properly. One of the most common issues is the OE error code. It means that there is a fault with the drainage system of an appliance.

If there is an OE code on LG dishwasher, there are many solutions to such a problem. Read below to find out typical issues and solutions to the error code of the appliance.

What Does OE Mean On LG Dishwasher?

If you have a new LG dishwasher, it may be disappointing to see an error code like OE show up on the water cycle, but don’t worry — it’s most likely a minor fault. Make the following to check why the LG direct drive dishwasher not draining:

• first, ensure that the drainage hose is properly attached, with no kinks or damage;
• if everything looks to be in order, remove the cap that connects the hose’s end to the disposal area;
• if it is still valid, it is time to call a specialist. 

However, if you have used the LG dishwasher for a long time, find out the potential solutions to being LG dishwasher clogged.

Problem	Description	Solution
Blocked Filter	A blocked filter is a common reason for the OE error code. This issue doesn’t allow the LG dishwasher to drain water in the bottom properly, causing the error to happen.	To resolve this issue, take the dishwasher filter and clear it of any dirt or clogs. Cleanse the element under warm running water with a brush to reach into all the spaces and crevices before reinstalling it into the device. Try to switch the appliance on again to identify the LG dishwasher OE error fix.
Clogged Air Gap	The air gap is an essential component of the device’s filtering process. It prevents gasses and contaminated water from recirculating up the LG dishwasher drain button and the appliance. It periodically becomes filled with debris and must be cleaned.	To start with, ensure that the dishwasher is turned off, and you have all the necessary supplies. Repairing the air gap and plastic covers might seem difficult. However, if you follow this guide, it will be simple. Inspect for visible dirt and use a toothpick or bottle brush to remove it. For a proper cleansing, insert warm water into the gap using a turkey baster. This technique will take a few minutes, but it will bring the best result. Don’t forget to change the cap and cover when you finish the cleansing process.
Clogged Drain Hose	One of the most prevalent issues with the OE error code is a blocked or clogged drain hose. A blocked hose may stop the dishwasher from effectively draining water, resulting in the OE error code. To resolve this issue, inspect the drain pipe and ensure that it is not kinked or failed.	In the beginning, inspect under your sink to see if there are any kinks where the drainage hose enters the garbage disposal. If the drainage hose has any kinks, has been broken, or has begun to leak, this is the cause of your OE fault, and it must be changed. If the hose is clogged, unplug and rinse it with warm water, ideally outdoors, to avoid spilling. Clear the debris, fix the hose, and set up the dishwasher again.
Faulty Drain Pump	A drain pump removes unclean water from the dishwasher during the washing process.	A broken pump may fail to drain water properly, leading to the OE error code being displayed. In this case, call a plumber or technician assistant to get the drain pump test.

How to Drain LG Dishwasher?

Your dishwasher might fail to drain even if there are no clogs. If you’ve tried all options, an LG dishwasher force drain might clean all of its sensors.

Firstly, look in the manufacturer’s guide for the CANCEL and DRAIN maintenance. It can be enabled by holding down two specified buttons, which differ according to the model.

If the LG inverter direct drive dishwasher error codes appear again, launch a washing cycle, wait 45 seconds, and then turn it off. These first 45 seconds of any cycle are just a drain, so this technique will make the dishwasher function.

Final Thoughts

If you noticed the LG dishwasher OE error code, don’t worry! The options listed above can solve the troubleshooting. Remember to observe the drain hose, filter, and proper set-up of the appliance. They are the important reason for the OE error code.

If the LG dishwasher not draining at end of cycle, you can check the panel flashing control for failures. If the flashing light doesn’t operate properly, it may lead to an OE error code. That is why, you should identify whether your appliance is within the warranty to change the unit.